• Excellent Material: METRIC VERSION Made of stainless steel, engraved, rustproof and corrosion resistant, not easy to wear and deform. WITH CARRYING POUCH
• For Welding Measuring: The welding inspection gauge can be used to measure the height of flat welds and fillet welds.
• Wide Range: The measuring range of the welding inspection gauge is 20mm, and the measuring range is wide and practical.
• For Weld Size Checking: Automatic weld gauge can check the throat of the fillet weld and determine the size of the weld leg of the fillet weld.
• Easy Control: The fillet weld gauge can be adjusted, and the concavity or convexity of the weld can be controlled.

TAPER GAUGE

Taper Gauge Measured Root Gap
Taper Gauge Measure Hole Diameter

Pocket Fillet Weld Gauge

This rugged gauge, fabricated in stainless steel, is made of sets of 2 Blades with permanent markings. Gauge leaf can check welding actual throat size and fillet weld leg sizes. It is useful for Welding, Maintenance & Quality Department. Both the leaves are assembled in handy chain

With a pivoting blade for easy measuring of eleven most specified fillet dimensions. Measures concave or convex seams. Stainless steel blades, etched increments. 3~25 mm, Each leaf has two ends  The gages possess two ends with one piece. One end is for convex fillet, and the other end is for concave fillet. Gauge used high quality stainless steel, the users can used them many times with less worn out.  The gauges comes as a set of individual gauges that used to size fillet welds. In fact, the gauge do not measure fillet welds. Only to determine whether the weld is smaller than, larger than, or the exact size of the gauge being used. The set of leaves of the fillet weld gauges like thread gauge go or no go.

Note: The gauge only tells you whether the fillet size "go" or "No go", smaller or larger than the standard.  The inspector checks the size of the actual weld by using one or more gauges to compare the size of the weld to the size of the individual gauges.

V Wac Welding Gauge

V Wac Welding Gauge is easily and quickly checks the four essential measurements required for compliance with NRC Visual Weld Acceptance Criteria. It checks undercut depth, porosity comparison, amount of porosity per linear inch and crown height, quickly determine if fillet welds meet NRC Visual Weld Acceptance Criteria for structural weldments,

Vernier Welding Gauge

Vernier Welding Gauge Measure Butt Weld Reinforcement

Vernier Welding Gauge Measure Fillet Weld Throat Thickness

Verrnier Welding Gauge Check Angel of Preparation  60, 70,80 & 90 Degree

Welding Profile Gauge, Welding Profile Comb, Weld Profiler, Contour Gauge, also known as Weld Profile Gauge, Profile Comb, or weld Profiler

A weld profile gauge is just the right tool for testing welding profile, matching wheel arches and body contours, or forming panels. Simply press the gauge against the piece you want to copy. Pull it away, and there's your reproduction.

?Measure Butt Weld Reinforcement, Weld Width, Root Gap

?Measure Fillet Weld Size, Throat Thickness, Depth of  Undercut

?Measure Angel of Preparation, Offsets

?Sturdy and Rust proof Made with stainless Steel

Welding Hi-Lo gauge. Measures internal , Fit-up gap, Bevel on Pipe and Plate end preparation, Crown height, and Pipe and Plate wall thickness. Fit-up gap; Internal misalignment; Weld crown height; Scribe line, socket welds; Fillet weld size; Pipe wall thickness; Angle of bevel on end preperation to an accuracy of 0.8 mm (1/32”).

Single Purpose HI-LO  Welding Gage is designed for internal alignment and determining root weld spacing, Internal HI-LO gage. Four quick steps check internal alignment You can check the internal alignment of your fit-up

permit you to accurately check welds of varying sizes quickly and easily. You can measure Weld Throat Thickness, Butt Fillet Type Welds, Weld Length, Misalignments (High-Low), and much more depending upon the Gauge selected. This digital welding gauge, with the designed based on a digital vernier caliper with direct reading, Its easy to use and provides fast and accurate measurements of surface pits, gauges, dents, undercuts, etc Weld Measuring Gauges are sturdy, well-made, and come in numerous types to perfectly fit your requirements.